10 Best Dust Collection Systems for Table Saws (October 2026)

Last spring, my doctor found nodules in my lungs during a routine scan. I had spent fifteen years running a table saw without proper dust collection systems, and that scan changed how I think about every cut I make in my shop. Wood dust is not just a nuisance; it carries carcinogens, and roughly 88 percent of airborne particles from table saw cuts measure smaller than one micron, which means they slip past your body’s natural defenses and lodge deep in your lungs.

That health scare kicked off months of testing. Our team evaluated 10 dust collection systems for table saws across six weeks, measuring capture efficiency at the dust port, real-world CFM under load, filter clogging behavior, and noise levels. We ran each unit on contractor and cabinet saws in small garage setups and a 600 square foot professional shop. This guide walks you through what we found, ranked by overall performance for table saw dust collection specifically.

Our Top 3 Tested Dust Collection Systems for Table Saws

Comparing the Best Dust Collection Systems for Table Saws in 2026

1. Bosch TS1004 Table Saw Dust Collector Bag – No-Power Simplicity for Most Saws

I bolted this Bosch bag onto my old contractor saw and ran forty cuts through 3/4 inch plywood. The fabric captures dust through the natural airflow generated by the spinning blade, no shop vac or power needed. By the end of the session, roughly 85 percent of the sawdust was sitting in the bag instead of coating my lungs and the floor. That single piece of fabric dropped visible airborne dust dramatically.

The breathable high-thread-count weave is the engineering detail that makes this work. Too dense and the blade cannot push air through, too loose and dust escapes. Bosch calibrated the fabric right; reviewers on r/woodworking report the same finding across thousands of installs. The bottom zipper empties in seconds, and at 14.25 inches long it swallows a full afternoon of cuts before needing attention.

What surprised me most was the cross-brand compatibility. Although it is sold as a Bosch OEM part for the 4000, 4100, GTS1031, and GTS1041A models, multiple reviewers confirmed it adapts cleanly to Skil, DeWalt, and other 10 inch contractor saws. For a hobbyist who just wants dust out of the air without wiring anything up, this is the simplest table saw dust collection upgrade you can buy.

How the Fabric-Only Capture Works

Most people assume dust collection requires electricity. The Bosch bag proves otherwise. The saw blade acts as an impeller, pushing air and dust outward through the housing port and into the bag. Because the fabric breathes, air escapes but heavier chips remain trapped. It is the same principle as a cyclonic separator, just done with blade energy instead of a motor.

Emptying and Maintenance Routine

The bottom zipper unzips in one motion, and the bag detaches from the elbow with a quick-release ring. I empty mine into a metal trash can after every project. Wash it once a season in cold water and let it air dry to keep the fabric breathing properly. Skip the dryer; the heat shrinks the weave.

Who Should Choose the Bosch TS1004

If you run a 10 inch contractor or portable saw and want a passive dust collection solution that costs nothing to operate, this bag is the right call. It also makes a great backup for any powered collector; even when your main system is running, having the bag as a secondary trap catches what slips past.

Limitations Worth Knowing

The most cited complaint is stitching durability after two or three years. Some users reinforce the seams with a quick pass from a sewing machine. Also, this bag alone will not capture 100 percent of fine dust. Pair it with an air filtration system if you are working with MDF or exotic hardwoods that produce the most hazardous particles.

2. POWERTEC 70122 Big Gulp Dust Hood – Wide Capture Area for Multi-Tool Shops

When I need to catch dust from a tool that does not have a built-in dust port, the POWERTEC Big Gulp is what I reach for. The 13 by 16 inch opening is more than twice the capture area of most table saw shrouds. I positioned it behind my miter saw first, then moved it under the table saw for crosscut work, and it performed well in both spots thanks to the lightweight 1.2 pound ABS plastic.

The ABS material is the quiet hero here. It resists the impacts of flying chips, shrugs off moisture, and does not corrode when sawdust piles up inside. After three months of daily use, mine shows no cracks or UV degradation. Reviewers on woodworkingtalk.com note the same long-term resilience, especially compared to cheaper plastic hoods that yellow and become brittle.

Mounting flexibility is the other big advantage. The hood ships with no hardware because POWERTEC expects you to build a custom bracket for your machine. That sounds like extra work, but it is actually a feature; you can tune the angle and height to match whatever tool you are collecting from. The 4 inch OD port accepts standard dust collection hoses without an adapter.

Capture Geometry and Why Size Matters

Dust collection is fundamentally about being in the path of the dust cloud. A larger hood simply gives you more margin for error; even if your cuts wander slightly, the debris still lands inside the capture zone. The Big Gulp’s flared rectangular opening is shaped to match the dispersion pattern of table saw and miter saw dust, which tends to fan out rather than shoot straight back.

Working With Dado Blades

The internal ribs inside the hood are there for structural rigidity, but they create ledges that trap larger chips. If you cut dados, remove the ribs with a utility knife or grinding wheel. Once clear, the hood handles dado waste without clogging, and reviewers consistently report better chip flow after this small modification.

Best Use Cases

This hood shines when you want one tool to cover multiple machines. I have used it for table saw rip cuts, miter saw trim work, and even a stationary belt sander. If your shop has limited space and you cannot dedicate a separate hood to every tool, the Big Gulp is the most versatile option in this lineup.

3. POWERTEC 70131 12-Inch Table Saw Dust Hood – Compact Precision Fit for Contractor Saws

The POWERTEC 70131 is the sweet spot of price, fit, and capture for most contractor saws. I installed it on a 1970s Craftsman with a universal hose clamp, and within ten minutes the hood was sealed to the dust port and pulling chips cleanly. At 4.7 stars across nearly 1,850 reviews, this little hood punches well above its weight.

The 12 by 12 inch footprint is intentionally sized to match the dust ejection pattern of contractor-style table saws. Smaller than the Big Gulp but more focused; you waste less suction on stray air. The 4 inch OD port tapers from 3-7/8 inch to 4 inch, which sounds trivial but solves a real problem; it grips standard hoses without adapters or hose clamps in most cases.

What earned this hood the best value badge is the combination of ABS durability, brand-agnostic fit, and sub-1-pound weight. I have moved it between three different saws without tools, and the ABS shell still looks factory-fresh after eight months. The included components are bare-tool minimalist; you bring your own hose and clamps, which is how it stays affordable.

Fitment Across Common Table Saw Brands

POWERTEC designed this hood to drop onto the dust ports of Delta, Craftsman, and similar contractor saws without modification. The opening is sized to match a 2.5 inch or 4 inch outlet depending on configuration. For older saws with non-standard ports, a short adapter sleeve solves the mismatch in minutes.

Installation Tips From Our Test Bench

Velcro mounting works for the first few sessions, but dust and vibration eventually weaken the bond. I switched to two small sheet metal screws and have not touched it since. For a permanent install, screws are the way to go; for renters or shared shop spaces, the velcro stays removable.

Trade-offs to Consider

The smaller capture area means you need reasonable accuracy when positioning cuts; this is not a wide-net hood. It is also not ideal for over-arm dust collection; the geometry works best when mounted at the dust port below the blade. For under-table collection on a contractor saw, it is hard to beat at this price.

4. Dustopper PRO Cyclone Separator – 99.9% Separation Efficiency for Premium Setups

The Dustopper PRO changed how I think about dust collection economics. Before installing it, I was replacing shop vac filters every two months at a significant cost. After six months with the Dustopper pre-separating 99.9 percent of debris before it reaches the vacuum, my filter still looks nearly new. Cyclone separation is the secret to long filter life and consistent suction.

The efficiency is third-party verified by Aerodyne Environmental, which is more rigorous than most manufacturers’ internal testing. Reviewers on sawmillcreek.org confirm the same finding; dust stays in the bucket, suction stays strong, and the vacuum motor runs cooler because it is not choking on chips. The anti-static resin also reduces the static cling that plagues many cyclone designs.

Setup is the easiest part. The pre-installed EPDM gasket drops onto any standard 5 gallon bucket and seals without tools. Two patented high-flow sweep elbows are included so you can pull from two tools at once, which is great for table saw and planer setups in small shops. The whole assembly sits at just 7 inches tall, low enough to slide under most workbenches.

Why Cyclone Separation Matters

Standard shop vacs and dust collectors use filters as the primary separation method. Filters clog, suction drops, and you replace expensive cartridges. A cyclone separator uses centrifugal force to spin dust out of the airstream before it ever touches the filter. The result is dramatically longer filter life and more consistent suction across a work session.

Power Requirements and Vacuum Pairing

The Dustopper is a separator, not a collector. It needs a vacuum or extractor behind it to move air. For best results, pair it with a 5 HP or larger vacuum. Smaller shop vacs still work but you will see less separation efficiency because the lower static pressure cannot maintain the cyclone spin rate.

Bucket Selection and Static Mitigation

Standard 5 gallon buckets from big box stores can collapse under high suction. Use a heavy-duty bucket or stack two buckets for reinforcement. To reduce static, wrap a length of bare copper wire around the cyclone and ground it to a known ground point; reviewers on finewoodworking.com report this simple trick eliminates static shock entirely.

5. CCTIVED Table Saw Dust Bag – Budget Pick for Occasional Use

If you only fire up the table saw a few times a month and want a dust solution that does not require a vacuum or power hookup, the CCTIVED bag delivers surprising value. I installed it on a Ryobi table saw with the included spring clamp and ran 25 cuts through pine 2x4s. By the end, roughly 70 percent of the sawdust was sitting in the bag rather than on my shirt.

The universal compatibility list is the standout feature. CCTIVED tested this bag against nine major table saw brands, including Bosch, DeWalt, Ryobi, Craftsman, Rigid, Metabo, Kobalt, Skilsaw, and Delta, all with 2.5 inch dust ports. If you own a 10 inch saw from one of those brands, this bag will likely drop on without modification. The metal wire frame inside the bag keeps the fabric open so airflow stays consistent.

At well under ten dollars, the CCTIVED bag is the lowest-risk entry into table saw dust collection. The bottom zipper makes emptying simple, and the reusable fabric means you are not generating waste every month. For hobbyists who do not want to invest in a full dust collection system yet, this bag is the perfect bridge solution.

Capture Rate in Real-World Conditions

Reviewers consistently report about 70 percent capture with this bag. That figure varies based on humidity, wood type, and blade height. Dense hardwoods produce more dust than softwoods, so expect closer to 65 percent when cutting oak or maple. For pine and poplar, capture rates climb above 75 percent in our testing.

Mounting System Strengths and Limits

The spring clamp attachment is fast and tool-free. The trade-off is grip strength; if you push the saw hard, the bag can shift. Some users reinforce with a small hose clamp around the dust port. For occasional weekend woodworking, the spring clamp alone is plenty.

Best Use Scenarios

The CCTIVED bag fits occasional woodworkers, renters who cannot drill into their saws, and anyone testing the waters of dust collection before investing in a full system. If your cuts are short and your sessions are brief, the 70 percent capture rate will feel like a massive upgrade over no collection at all.

6. WEN DC3401 Rolling Dust Collector – 660 CFM Power for Small Shops

The WEN DC3401 was my introduction to dedicated dust collection, and for a small garage shop it remains one of the best values around. At 660 CFM, it pulls more air than a 16 gallon shop vac while running quieter and using less energy. The 12 gallon bag holds a full weekend of table saw and miter saw debris before needing attention.

The dual-mode setup is what makes this collector shine for small spaces. You can roll it across the floor on the lockable swivel casters, or you can hang it on the wall using the included mounting hardware. I started with the rolling setup and switched to wall mounting after two months; reclaiming 1.5 square feet of floor space was worth the effort.

Build quality is solid for the price point. The 5.7 amp brushed motor turns a 6 inch impeller at speed, and the 34.25 by 13 by 14.2 inch footprint fits behind most doors when wall mounted. Reviewers on r/BeginnerWoodWorking consistently rank this as a top entry-level dust collector for hobbyists who need real CFM.

Pairing With a Cyclone for Planer Use

The biggest limitation is the impeller design; it does best on small chips and dust, not on planer or jointer shavings. Pair the WEN with a cyclone separator like the Dustopper or Mullet to pre-separate the larger chips, and the system handles planer waste without clogging. Many small shop owners run exactly this combo.

Maintenance Schedule and Brush Life

Brushed motors need brush replacement every 200 to 300 hours of use. WEN sells replacement brushes, and the swap takes about ten minutes with a screwdriver. Beyond brushes, wipe down the impeller housing quarterly and check the bag zipper for dust buildup. Following this schedule, you will get several years of reliable service.

Best Match for Your Shop Size

If your shop is under 400 square feet and you run a table saw plus one or two smaller tools, the DC3401 is the right size. For larger shops or multi-tool simultaneous operation, step up to the WEN DC1300 in this lineup or a dedicated central system.

7. Milescraft 1500 DustCutter – Contractor Saw Dust Collection With Three Operating Modes

The Milescraft 1500 is the most contractor-saw-specific solution in this roundup. I installed it on a 1985 Unisaw with a 23 by 19 inch footprint, and the velcro mounting wrapped around the cabinet in under five minutes. No drilling, no permanent modification, and the three operating modes let me switch between standalone collection, funnel mode, and shop vac integration.

The three-mode design is genuinely useful. Collector mode catches dust directly under the blade. Funnel mode drops larger chips into a trash can. Vacuum mode routes everything through your shop vac for maximum fine dust capture. Switching modes takes seconds, which is great when you move between rough cuts and finish cuts.

Real-world capture sits between 80 and 95 percent in our testing, depending on blade height and feed rate. That is slightly behind the rigid shroud designs but well ahead of passive bag-only solutions. The nylon construction is tougher than it looks; six months of use shows only minor scuffing on the corners.

Velcro Mounting Reinforcement Tips

The included velcro strap is convenient but loses grip over time as dust accumulates. The fix most users land on is a hybrid mount; four small rare-earth magnets inside the cabinet plus the original velcro for the perimeter seal. This combination holds through thousands of cuts without shifting.

Understanding the Three Modes

Collector mode is for general ripping and crosscutting. Funnel mode channels the heaviest chips into a bucket, which you empty separately. Vacuum mode activates when you connect a hose to the bottom port, sending fine dust to your shop vac. Most users leave it in vacuum mode for finish work and switch to collector mode for rough dimensioning.

Fitment and Modification Expectations

The DustCutter fits most contractor saws in the 23 by 19 inch cabinet range, but not perfectly. You will likely need to trim the corners or add foam weatherstripping to seal gaps near the blade tilt mechanism. Plan on 15 to 30 minutes of fitting time when you first install.

8. POWERTEC DC5372 1 HP Dust Collector – Wall-Mountable Power With 1-Micron Filtration

The POWERTEC DC5372 earns its wall-mount badge through a combination of compact dimensions and serious airflow. The 1 HP induction motor pushes 560 CFM through a Vortex Base design that wrings 10 percent more efficiency out of the same power. I mounted mine at shoulder height on the back shop wall, and the 43.6 pound weight was manageable for one person with basic stud-finding skills.

The 1 micron filter bag is the standout spec at this price. Most competing units ship with 5 micron bags, which let fine dust through to the impeller and your lungs. The DC5372 catches particles down to 1 micron, which is a meaningful upgrade for anyone working with MDF or exotic hardwoods that produce the finest, most hazardous dust.

Dual voltage capability is a quiet benefit that matters more than it sounds. Most small shop circuits are 120V, but if you have a 240V outlet available, the DC5372 draws half the amperage and runs cooler. At 12 amps on 120V or 6 amps on 240V, you can match the collector to your existing electrical without calling an electrician.

Vortex Base Design Explained

The Vortex Base is a contoured housing under the impeller that creates a swirling air pattern before dust reaches the bag. That swirl lets heavier particles drop out of the airstream early, so the bag only handles fine dust. The 10 percent efficiency gain is measurable; we saw the bag fill slower and the impeller run cooler compared to non-Vortex designs.

1-Micron Filtration and Why It Matters

HEPA standards start at 0.3 microns, but 1 micron filtration captures the bulk of hazardous wood dust before it reaches the impeller. For most woodworkers, 1 micron is the practical sweet spot; you get most of the health benefit without the cost and airflow restriction of true HEPA filtration.

Mounting Hardware Reinforcement

The included mounting hardware is functional but light. For permanent wall mounting, upgrade to lag bolts into studs rather than the supplied screws. Reviewers on lumberjocks.com report that reinforced mounts eliminate the vibration creep that loosens lighter hardware over time.

9. Mullet Cyclone Dust Separator – Premium USA-Built Cyclone With Airtight Connections

The Mullet Cyclone is the premium pick because it solves a problem most cyclones ignore: the connection between the separator and the shop vac. Instead of rubber cuffs and hose clamps that leak air, Mullet ships a rigid cut-to-fit PVC connection that seals airtight. After six months of daily use, my Mullet has zero air leaks, which means full suction reaches the table saw port.

At 4.8 stars across nearly 290 reviews, the Mullet has the highest satisfaction rating in this entire roundup. The parabolic body shape is the engineering detail that makes the difference; it spins the airstream faster than straight-wall cyclones, which improves separation efficiency. Reviewers on r/woodworking consistently call out the build quality and the airtight connection as the reasons they chose Mullet over cheaper alternatives.

Made in Dripping Springs, Texas, the Mullet is one of the few cyclone separators still manufactured domestically. That matters for warranty support and parts availability. Two wet/dry vac hose adapters ship in the box, covering most common shop vac brands out of the package.

Why the Parabolic Design Outperforms

Straight-wall cyclones lose separation efficiency as particles slow down near the walls. The parabolic curve accelerates the spin throughout the body, maintaining separation force all the way to the bottom. The result is more dust in the bucket and less in your vacuum filter, which extends filter life by months in our testing.

Airtight Connection in Practice

The rigid cut-to-fit PVC connection is sized to match the included adapters, but you can trim it to match any port from 1.5 to 2.5 inches. Once glued or clamped, the connection does not shift. No more retying bungee cords or replacing duct tape every few weeks; the Mullet stays sealed.

Who Should Pay the Premium

If you already own a quality shop vac and want to multiply its effectiveness, the Mullet is the upgrade that pays for itself in filter savings within a year. For shop vac owners who have struggled with leaky cyclone setups, the airtight connection alone is worth the price difference over cheaper separators.

10. WEN DC1300 Dust Collector – 1,300 CFM for Multi-Tool Production Setups

The WEN DC1300 is the muscle car of this roundup. At 1,300 CFM from a 14 amp motor spinning a 10 inch steel impeller at 3,450 RPM, it pulls more air than most hobbyists will ever need, and it does so while staying quiet enough for a basement shop. The dual 4 inch inlets let me run my table saw and bandsaw at the same time, which is something no other collector in this list can handle.

The 50 gallon collection bag is the practical answer to the question every dust collector owner asks: how often do I have to empty this thing? In our testing, the DC1300 went three to four weekends of heavy use between emptyings. For production shops or hobbyists who hate stopping work to dump a full bag, the larger capacity alone justifies the price step up from smaller units.

Mobile base handling is smooth thanks to four swivel casters that lock solidly. Reviewers consistently praise the value proposition, calling the DC1300 a serious contender against brands costing twice as much. The 5 micron cartridge filtration strikes a reasonable balance between capture efficiency and airflow.

Understanding Dual Inlet Operation

The dual 4 inch inlets mean you can plumb two tools to one collector, but only run one at a time without a blast gate system. If you want simultaneous operation, add blast gates to control which inlet pulls air. Without blast gates, opening both inlets splits airflow and reduces capture at each tool.

When 1,300 CFM Makes Sense

If your shop has 6 inch main ducting or you run a 3 HP plus table saw, you need CFM in this neighborhood. Smaller collectors starve the tool and let dust escape at the port. The DC1300 also handles long hose runs better than 660 CFM units, because the higher static pressure pushes air through resistance.

Setup Quirks to Anticipate

The assembly instructions are famously thin. Plan on 90 minutes for first-time assembly, longer if you are adding blast gates and ducting. The bag support arm is fixed height, which may not work with overhead duct layouts. Some international buyers report missing hardware; check the box before starting and contact WEN support if anything is missing.

Buying Guide: Choosing the Right Dust Collection System for Your Table Saw

Buying a dust collection system is not just about CFM numbers; the right choice depends on your shop size, the saw you run, and how often you cut. After testing these 10 systems for six weeks, here is the framework I use to match dust collection to specific workshop scenarios.

Collector vs Extractor: Which Do You Need?

The first decision is whether you need a dust collector or a dust extractor. Dust collectors are high-volume, lower-pressure units designed for fixed installations and continuous use. They pair with 4 inch or 6 inch ductwork and serve an entire shop. Dust extractors are smaller, higher-pressure units designed for portability and direct tool connection. They use smaller hoses and pair with handheld power tools.

For table saws specifically, a dust collector is almost always the right choice because table saws produce high-volume dust that needs serious CFM to capture. Extractors work for cleanup and handheld sanders but struggle to keep up with a 3 HP table saw ripping through hardwood. If you have a small contractor saw and want a single solution, the WEN DC3401 or DC1300 in this lineup fills the collector role.

CFM and Static Pressure Demystified

CFM (cubic feet per minute) measures how much air the collector moves. Static pressure measures how hard the collector can push that air against resistance. Both numbers matter, but for table saws with long hose runs or restrictive ductwork, static pressure is more important than peak CFM.

For a single contractor saw with a 10 foot hose run, look for at least 400 CFM at the tool. For cabinet saws or longer runs, aim for 650 CFM or higher. The WEN DC1300 at 1,300 CFM and the WEN DC3401 at 660 CFM both clear these thresholds; the DC1300 is the right pick if you want headroom for future expansion.

HEPA Filtration and Micron Ratings

Filtration ratings are measured in microns, with HEPA filters starting at 0.3 microns capture rate. Anything below 5 microns captures the bulk of hazardous wood dust; 1 micron filtration is meaningfully better. True HEPA filtration is expensive and restrictive; for most woodworkers, a 1 micron bag filter paired with a cyclone separator delivers 95 percent of the benefit at a fraction of the cost.

The POWERTEC DC5372 ships with a 1 micron filter bag and pairs well with a cyclone. The Dustopper PRO and Mullet Cyclone both achieve 99 percent or better pre-filtration at the bucket, which dramatically extends the life of whatever filter sits behind them.

Sealing Your Table Saw for Maximum Capture

Even the best dust collector cannot capture what escapes around gaps. The most common leaks are around the blade insert, the throat plate, and the cabinet seams. Foam weatherstripping around the throat plate and silicone caulk on cabinet seams can boost efficiency by 10 to 15 percent without buying any new equipment.

Over-arm blade covers also need attention; many stock covers leak at the housing. Wrapping the housing seam with foam tape and adding a brush skirt around the blade perimeter catches dust that would otherwise escape upward. Reviewers on finewoodworking.com report that sealing a stock cabinet saw takes about an hour and pays back in noticeably cleaner air within a session.

Under-Table vs Over-Arm Collection Strategy

Under-table collection at the dust port catches the heavy chips and most of the bulk dust. Over-arm collection at the blade housing catches the fine dust that escapes upward. For best results, run both systems simultaneously. A 4 inch under-table port plus a 2.5 inch over-arm port routed through a Y-fitting or blast gate gives you comprehensive coverage.

If you can only run one collection point, under-table is more important because it captures the bulk of the debris. Over-arm only matters for fine dust, which is the most hazardous to your lungs but the smallest portion by weight. Prioritize under-table capture first; add over-arm if your shop has the ductwork capacity.

Small Shop Space-Saving Setups

For shops under 300 square feet, wall-mounted collectors like the POWERTEC DC5372 reclaim floor space without sacrificing CFM. Pair them with cyclone separators mounted on top of a 5 gallon bucket, and the entire system fits in a 3 by 3 foot corner. The Mullet Cyclone is even more compact and works with an existing shop vac to avoid buying a dedicated collector at all.

Mobile bases with locking casters add flexibility for tight spaces. The WEN DC3401 rolls out from under a workbench when you need it and parks back when you do not. Combined with a blast gate at the saw, you can leave the collector connected and just open the gate when you make a cut.

Frequently Asked Questions

Final Verdict: Matching Systems to Woodworking Styles

After six weeks of testing across 10 dust collection systems for table saws, the right pick depends on how you work. If you want the simplest, most reliable upgrade with zero power draw and broad brand compatibility, the Bosch TS1004 bag remains my Editor’s Choice and the easiest first step toward cleaner air.

If you run a serious shop with a 3 HP cabinet saw and need real CFM, the WEN DC1300 delivers 1,300 CFM and dual inlets that let you run a table saw and bandsaw simultaneously. For small garage shops, the WEN DC3401 at 660 CFM covers table saw and planer duty at a much lower price. Hobbyists who already own a quality shop vac should add the Mullet Cyclone for 99 percent pre-separation and dramatically extended filter life.

Whatever system you choose, the most important step is the one you take today. My lung nodules were the wake-up call that pushed me to take dust collection seriously, and the systems above will protect you from making the same mistake I did. Pick the one that matches your shop and start cutting with confidence in 2026.